October 24, 2014

SOUNDVAPE LIQUIDATION: 10ML OF EJUICE – 99 CENTS!

I picked up this little gem in the Vaporjoes Facebook group.

Soundvape is going out of business and they are liquidating everything at up to 90% off.   Their hardware selection isnt the best but the ejuice looks pretty good.  They are selling 10ml bottles for just 99 cents each.  This wasnt some fly by night company – they have been around a while.

For the price?  Pick up a few!

WHERE: >> HERE <<

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

SEXY STAND: 70 HOLE MOD STAND – $47.89

Chinese mod stands are getting pretty nice these days and this one looks pretty epic. This mod stand as 70 holes that’s going to easily hold the average vapers entire mod collection.

These are also fantastic for brick and mortar displays.  I picked one up to check out.

WHERE: >> HERE <<

$47.89

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

LOWEST: THE ELEAF ISTICK DROPS AT $29.99 + FREE SHIPPING

 

WE ALL LOVE THE ISTICK!  Its ULTRA portable.  Smaller then the original vaporshark – this little mod lasts a long time and packs 20 watts of power.

I was so impressed I bought 3 more.

THE HARD COPY:

  • 2200mAh Li-Ion Battery
  • VV/VW – up to 20W and 3v – 5.5v
  • OLED display
  • 510-Threads
  • Power on/off: Press the button for five times to turn the iStick on and off.
  • 10-sec Protection: Maximum of 10 seconds per drag.
  • Atomizer Short-Circuit Protection: If atomizer short-circuits, the OLED screen show “Atomizer Short”.
  • Low-Voltage Protection: Once the battery is below 3.3V the OLED screen will show “Lock”, which means its time to recharge.
  • Unlock the Low-voltage Protection: The iStick begins working again once it reaches 3.65V.
  • Low power Alert: If the battery’s power is lower than 10%, the power symbol on the screen will flash.
  • Atomizers from 1ohm to 3ohm capable
  • Accurate Metering
  • Pass-Thru vaping while charging
  • Charged via micro usb
WHERE: >> HERE <<

$29.99 + FREE SHIPPING

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

October 22, 2014

BUZZ: THE BIG BUDDHA RDA – $36.75

http://bit.ly/1t5xOeM
There is a lot of buzz about this Kayfun style rebuildable from EHPRO.

This is a 29.5mm sized device for your 26650 mods. It features a kayfun style build with a bigger building deck and can handle dual coil builds. It has 2 airflow holes with 2 adjustable airflow controls on the bottom side like the Kayfun 3.1. It includes a glass tank as well as a metal tank which can hold up to 10ml of juice!

THE HARD COPY:

  •     Fit best with 26650 Mods
    Made out of 304 Stainless Steel
    SS center post with SS screws
    Two Adjustable Air-flows holes
    Comes with a Pyrex Tank and a Stainless Steel Tank
    Comes with a matching drip tip
    29.5mm in diameter
    49.2mm in length (Tank Section)
    Engraved with EHpro Logo
    Serialized
    Great for doing dual coil builds
    Original & Affordable
WHERE: >> HERE <<

$36.75

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

TRIQUETRA STYLE MECHANICAL 18650 / 26650 – $29.21

http://goo.gl/f62YjP
This unique mod can use both 18650 and 26650 batteries.
The inner tube allows for the 18650 and if you remove it – you can use a 26650.

THE HARD COPY:

  • Recessed 510 connection
  • Adjustable copper positive contact
  • Solid brass negative contact
  • Copper 26650 body diameter: 29mm
  • Brass 18650 body diameter: 22mm
  • Brass top cap and bottom cap
  • Bottom spring-loaded firing button w/ reverse-threaded copper locking ring
  • Adjustable delrin firing pin insulator
  • Engraved logo
WHERE: >> HERE <<

$29.21

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

ROLLOUT: THE FATBABY 100 WATT MOD BY PROJECT SUB-OHM – $99

http://www.vapordna.com/ProductDetails.asp?ProductCode=FB0001&Click=98


“fatbaby” By Project Sub-Ohm™

Even since the introduction of the “littlemaN’™ Box mod, the “littlemaN”™ has gain a huge popularity among the world of vapers! Now Project Sub-Ohm™ has found a perfect platform to build on its third box mod. The “fatbaby”™ 100 Watts Mod made by Project Sub-Ohm. The goal is simple, to create an affordable yet still super powerful device that can satisfy majority of the vapers out there!

Product Includes:

  • 1 x “fatbaby”™ Mod by Project Sub-Ohm™
  • 1 x screwdriver
  • 4 x copper center pins
  • 4 x stainless steel screws for back battery door
  • 1 x instruction manuel
  • 1 x signature “fatbaby” Mod gift box with Project Sub-Ohm™ and ‘fatbaby”™ logo


Product Descriptions:

The “fatbaby”™ series by Project Sub-Ohm™ is a powerful Variable Wattage Device that can adjustable it’s power from 10W to 100W in increments of 0.1 Watts! This device uses upgrade YiHi SX330 Chip, which is capable of firing coils at 0.15 ohm up to 3.0 ohm. The “fatbaby”™ Mod is powered by a dual IMR 18650 battery and is capable of producing up to 100 Watts of power! The two screws on the back of the device hold the battery cover firm and sturdy, additional two magnets are in installed as well to hold the back battery cover without the use of the screws for ease of swapping batteries. The battery is removable, so changing batteries are a breathe to do. The OLED screen is bright and easy to read, and also shows you the wattage, resistance, output voltage and battery life.

Product Features:

  • Beauty screen and greeted with “fatbaby”™ when turned on
  • Full Aluminum Body For rigidity!
  • Capable of firing 0.2 ohm – 3.0 ohm build
  • Capable of putting out 100 Watts of power!
  • Beautifully Engraved With Project Sub-Ohm™ Logo and “fatbaby”™ logo
  • Serialized (Roman Numeral Serialization, I, II, III and so on)
  • Roman Numeral Serialization is an extremely labor intensive work, each number is manually adjustable with live people!
  • Matches all other Project Sub-Ohm™ products
  • We Made It Powerful! We Made it Affordable!
  • Unique and Elegant “fatbaby”™ gift box packaging. (Highly Sought After!)

Product Specs:

  • Output Power: 10W – 100W
  • Output Voltage: 1.5V – 7.0V
  • Loading Resistance: 0.15 ohm – 3.0 ohm
  • Output Short Circuit Protection
  • Reverse Battery Protection
  • Dimension: 102mm x 56mm x 23mm (2-3/16″ x 4″ x 7/8″)

Product Recommendations:

  • FOR USE WITH 30 AMPS OR HIGHER IMR BATTERIES ONLY!
  • Please do not put in your battery in wrong direction
  • Make sure battery sit completely snug in the battery slot
  • Do not use any batteries if the outside wrapper has come off!
  • Turn off the device before pulling your battery out
  • Do not wrap your coils below recommanded ohm level and always vape safe!
  • 510 pins are reverse threaded, do not force it pin does not turn
  • Alway turn off the device and take the batteries out when not in use!
  • Center pin is reverse threaded, do not force turning! (Screw right for pin to up, screw left for pin to go down)
WHERE: >> HERE <<

$99

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

October 21, 2014

REPLICATED: THE LITTLE BOY RDA – $10.19

http://myurl.co/littleboyrda
Seems the evil clone empire has been working over time.    Cranking out new replicas faster and faster.  I’m hearing this particular one is pretty bad ass and very close to the original.

THE HARD COPY:

  • Compatible with 510 drip tip (drip tip sold separately)
  • The POM top cap lid is removable
  • The lid also works as a heat insulator of the drip tip
  • 510 threading connector, adjustable copper 510 center pin
  • Tri-post design for single/dual coil build
  • Posts material: Stainless steel
  • Air flow adjustable, 3 air slits on the sleeve
  • Engraved logo
  • 22mm diameter
  • Comes with a POM top cap lid + drip tip 2-in-1 combo
WHERE: >> HERE <<
$10.19
Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

USA DEAL: CERAMIC TWEEZERS – $10.99

NOW AT A NEW LOWER PRICE FROM THE USA!

The photo above is what inspired me to start looking into these.  You see what they are doing?  Making a micro coil right deck of the rebuildable – by firing the PV.  Since the tweezers are heat resistant (ceramic) it gives the user a whole new way to rebuild with ease.

If you rebuild – you need these.

WHERE: >> HERE <<

$10.99

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

October 20, 2014

THE $13.00 COLONIAL REPLICA

http://goo.gl/zjwBRb
Inspired by the ‘Colonial’, this replica is constructed of aluminum with an army green colored finish. Contacts are copper and positive pin is adjustable. Mod houses a single 18650 battery. The recessed bottom-firing switch is sets this mod apart.

THE HARD COPY:

  • 510 threading connection
  • Copper contacts (adjustable)
  • Recessed curved firing button to prevent accidental firing
  • With logo engravings
  • Houses single 18650 battery (battery sold separately)
WHERE: >> HERE <<
$13.93
Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

TWO SAMSUNG INR 18650 25R BATTERIES – $16.94 + FS

http://bit.ly/1wqKPjP
With Sony officially ending its production of all 30 amp 18650s – the Samsung 25R has started taking its place.  They are plentiful, cheap, and reliable!    This deal your getting two + a plastic carry case for this low price!

This deal is hard to beat out of the USA with free shipping.

– Type: Lithium-ion
– Composition: LiMn Hybrid (IMR)
– Rechargeable: Yes
– Top style: Flat top
– Capacity: 2500mAh
– Max continuous discharge: 20A
– Nominal voltage: 3.7V
– Full charge voltage: 4.20V±0.05V

WHERE: >> HERE <<

$16.94 + FREE SHIPPING

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

October 19, 2014

(UPDATE) THE 180 WATT GOD MOD HITS FASTTECH FOR $98.00

http://myurl.co/gm2

This is why the DNA40 is too little … to late!

You wont find it cheaper ANYWHERE else.

Now we found a very cheap source to actually get one.  This wattage behemoth uses 3 x 18650 batteries and hits a maximum output of a whopping 180 watts!

We thought $1.00 per watt was cheap, now we are looking at about 50 cents per watt.

THE HARD COPY:

  • Capacity  Use 3 18650 batteries
    Input voltage 9.9v-12.6v
    Output voltage 1v-12.6v
    Size 119x69x30(mm)
    Color Red,blue,silver,orange,black
    Resistance 0.5-4ohms
    Wattage(PMW) 5-180w
    Material Aluminum
    Big currents protection Yes
    short circuit protection Yes
    Reverse battery protection Yes
    Low voltage protection Yes
    Low resistance protection Yes
    Temperature protection  Yes
WHERE: >> HERE <<

$98.48

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

REPLICATED: THE ZERO FALLS VICTIM TO THE EVIL CLONE EMPIRE

WHERE: >> HERE <<

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

October 15, 2014

TUGBOAT VERISON 2 REPLICA LANDS AT $8.96

http://goo.gl/uB8ihl
The Tugboat Styles are widely regarded as a great, simple, no nonsense atomizer. The version 2 brings a cleverly designed top cap with two parts to allow you to easily adjust your airflow without the need to grab a drill. Wide bore drip tip is included. Constructed of stainless steel.

THE HARD COPY:

  • Stainless steel 510 drip tip
  • 4 air holes or 2 air holes option
  • Deep juice well (approximately 3.6mm deep)
  • Tri-post design
  • Posts material: Chromed brass
  • 510 connection (chromed brass center pin)
  • 22mm external diameter
  • Height without drip tip: 29.5mm
WHERE: >> HERE <<

$8.96

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

CHEAP AND EFFECTIVE: THE $5.99 RDA SHIPPED FROM THE USA

Basic, cheap, and effective!

The Dripper RDA is exactly what you think it is: a rebuildable dripper. This is a very basic design, perfect for someone who wants to get into rebuilding. There’s a 1 positive and 1 ground post, ideal for single-coil builds. Airflow has been improved over past RDAs, in that the airflow comes in from a hole in the side, instead of at the bottom of the deck. This also means reduced leaking. The top cap also features an integrated mouthpiece for a uniform look. The Dripper comes with a pre-made coil.

For $5.99 is a great little dripper!

WHERE: >> HERE << 

$5.99

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone

BLOWOUT: VAPORSHARK DNA 30 DROPS TO $119.00 + DNA40 PREORDER

Everyone knows what a HUGE fan I am of the Vaporshark.   To me the chip is secondary – its more build quality and support.  With the unveiling of the new DNA40 the DNA30 original size version has dropped to just $119.99 (50 bucks off).

A STEAL in this bloggers opinion.

They are also opening pre-orders on the new Vaporshark running the DNA40.

$119.00 DNA30 VERSION:  >> HERE <<

PRE-ORDER THE rDNA40:  >> HERE <<

Share on FacebookTweet about this on TwitterShare on Google+Share on LinkedInPin on PinterestShare on RedditShare on StumbleUponDigg thisEmail this to someone